EQQR000 - EQQR714

EQQR000E

YOU ARE NOT AUTHORIZED TO ACCESS THE READY LIST

You have attempted to access the ready list, but you are not authorized to access it.

The requested access to the ready list is rejected.

If you require access to the ready list, contact your security administrator.

EQQR008E

YOU ARE NOT AUTHORIZED TO ACCESS THE JS DATA SET

You have attempted to access the job setup facility, but you are not authorized to access it.

The requested access to the job setup facility is rejected.

If you want only to browse the JCL, you need read access authority. If you want to update the JCL, you need update access authority. Contact your security administrator.

EQQR010I

ERDR ERC# TERMINATED

Event reader ERC processing has completed and control is returned to the HCL Workload Automation for Z subsystem.

Event reader ERC processing is terminated.

None.

EQQR011I

EVENT READER ERC# HAS BEEN REQUESTED TO STOP

Event reader ERC. has been requested to stop while waiting for positioning information in the event data set to become available.

The event reader frees all acquired resources and is terminated.

None.

EQQR012I

ERDR ERC# RESTARTED

Event reader ERC has been restarted. This message is issued only for event readers that service the NCF application at remote sites. The probable reason is that the event reader is restarted either with new positions in the event data set after a control plan refresh or when an NCF session is reestablished after failure.

Event reader ERC restart processing continues.

None.

EQQR013E

ERDR UNABLE TO LOAD MODULE EQQERBEX - INITIALIZATION IS TERMINATED

An event reader task was unable to locate the EQQERBEX load module.

The event reader initialization is terminated.

Stop the event readers using the MODIFY command. Make sure that the EQQERBEX module resides in a load library that can be accessed by HCL Workload Automation for Z and restart the event readers.

EQQR014W

ERDR ERC# NO VALID HEADER IN EVENT DATA SET WITH DDNAME DDN

Event reader ERC encountered a header record that contained invalid information, for example, the track capacity and the total number of records in the data set were missing. The most probable reason is that a new event data set has been created and it is being formatted by the event writer before usage. The header record is not updated with the characteristics of the data set until the formatting job has completed. This might take some time if the event data set is large.

Event reader ERC processing continues. It makes a new attempt to extract valid information from the header record every 10 seconds. This message is written in the HCL Workload Automation for Z message log, with a frequency determined by the ERWAIT parameter. If ERWAIT is set to its default value (10 seconds), this message is written every minute until a valid header is read or until the HCL Workload Automation for Z subsystem posts a stop request. If ERWAIT is set to a value other than the default, this message is written with a frequency calculated according to the following rule: TIME FREQUENCY = ERWAIT_value x 6.

Use the MODIFY command to stop the event readers, correct the error, and restart the event readers.

If this message appears more than 10 times on the HCL Workload Automation for Z message log data set, stop the event readers. Check that the DDN ddname connects to the correct event data set, and if so, find out why the header record is not valid.

EQQR015E

SEQUENCE NUMBER SEQNO IS ALREADY IN USE BY AN EVENT WRITER SUBTASK

At event reader initialization, an event writer was already started with the sequence number specified in the ERSEQNO keyword of ERDROPTS.

The number specified in the ERSEQNO keyword of ERDROPTS must be unique within the HCL Workload Automation for Z subsystem.

The event reader initialization fails. The event reader subtask is terminated.

Update the ERSEQNO keyword with a unique sequence number and restart the event reader subtask.

EQQR021E

ERDR ERC# UNABLE TO OPEN EVENT DATA SET WITH DDNAME DDN

Event reader ERC could not open its associated input data set (ddname DDN).

Event reader ERC processing is terminated.

Use the MODIFY command to stop the event readers, correct the errors, if any, and restart the event readers.

Verify that the ddname statement associated with this event reader is correctly specified. The ddname is EQQEVDxx, where xx should be equal to ERC.

EQQR023E

ERDR ERC# RECORDS OVERWRITTEN ON EVENT DATA SET (DDNAME DDN) LR# EVENTS HAVE BEEN LOST

Event reader ERC encountered a situation where the event writer overwrites event records not yet processed by the event reader. Event data sets are used in a wrap-around fashion and for some reason the event reader cannot keep up with the event writer.

Event reader ERC processing continues. The event records that were overwritten (LR) are lost and cannot be recaptured.

Use the MODIFY command to stop the event readers, modify the appropriate parameters, and restart the event readers.

Describe the scenario that caused the error. To collect appropriate documentation for problem determination, see the Diagnosis Guide and Reference manual, Chapter 3. Problem analysis procedures. Search the IBM Support database for a solution at http://www.ibm.com/software/sysmgmt/products/support.

The problem is probably one of the following:
  • An inadequate allocation in the event data set, so that it wraps around too fast.
  • The wait interval (ERWAIT of the ERDROPTS statement) is too long, that is, the event reader waits too long between successive read attempts.
You should also check the dispatching priority of the reader task to make sure that its priority is similar to that of the event writer.

EQQR024E

ERDR ERC# TERMINATION DUE TO INITIALIZATION FAILURE

Event reader ERC has encountered initialization errors.

Event reader ERC processing is terminated.

Use the MODIFY command to stop the event readers, correct the errors, if any, and restart the event readers.

This message is preceded by other messages in the HCL Workload Automation for Z message log. They indicate the exact reason for the failure.

EQQR025I

ERDR ERC# STARTED

Event reader ERC has successfully completed its initialization processing and is now ready.

Event reader ERC processing continues.

EQQR026E

ERDR ERC# I/O-ERROR ON EVENT DATA SET WITH DDNAME DDN- SYNAD INFORMATION: SYNADMSG

Event reader ERC encountered an I/O error when reading its associated event data set (ddname DDN). The event data set is defined on the DDN ddname statement.

Event reader ERC processing is terminated.

Either correct the error and use the MODIFY command to restart the event readers or stop HCL Workload Automation for Z, correct the error and restart HCL Workload Automation for Z.

The SYNAD routine collects information such as jobname, stepname, unit address, device type, ddname, operation, error description, and access method. The SYNADAF macro is used to extract this information. For a detailed description of the layout refer to the appropriate documentation for the MVS/DFP product installed on this system.

EQQR027E

ERDR ERC# INITIALIZATION FAILED - KEYWORD SPECIFICATION MISSING

Event reader ERC found that the KEYWORD keyword was not specified on the ERDROPTS statement.

Event reader ERC processing is terminated.

Use the MODIFY command to stop the event readers, correct the errors, if any, and restart the event readers.

EQQR028E

ERDR ERC# INITIALIZATION FAILED - KEYWORD SPECIFICATION INVALID

Event reader ERC found that the keyword KEYWORD was not specified correctly on the ERDROPTS statement. If the ERSEQNO keyword specification was in error, ERC consists of **.

Event reader ERC processing is terminated.

Use the MODIFY command to stop the event readers, correct the errors, if any, and restart the event readers.

EQQR029E

ERDR ERC# INITIALIZATION FAILED - NO ERDROPTS STATEMENT SPECIFIED

Event reader ERC found no ERDROPTS statement in the member (specified on the OPCOPTS statement) that was to hold initialization parameters for an event reader. Because no event reader sequence number is available, ERC consists of **.

Event reader ERC processing is terminated.

Use the MODIFY command to stop the event readers, add a correct ERDROPTS statement to the member in error, and restart the event readers.

The HCL Workload Automation for Z message log contains messages that identify the parameter member that is in error.

EQQR101E

THE LAYOUT RLLAYOUT CANNOT BE ADDED TO THE LAYOUT TABLE

The ready list layout table already contains the layout that you tried to add.

The ready list layout table is not updated.

Change the layout name and repeat the request.

EQQR102I

THE LAYOUT RLLAYOUT HAS BEEN ADDED TO THE LAYOUT TABLE

The layout has been successfully added to the ready list layout table and saved.

The ready list layout table is updated.

None.

EQQR103I

THE LAYOUT RLLAYOUT HAS BEEN DELETED FROM THE LAYOUT TABLE

The layout has been successfully deleted from the ready list layout table.

The ready list layout table is updated.

None.

EQQR104I

THE LAYOUT RLLAYOUT HAS BEEN UPDATED IN THE LAYOUT TABLE

The layout has been successfully updated in the ready list layout table.

The ready list layout table is updated.

None.

EQQR105E

TO EXIT FROM THIS PANEL, EITHER SELECT A LAYOUT OR CANCEL THE REQUEST

A layout is required for the requested ready list display.

The system waits for you to respond.

Select an existing layout or create a new one.

EQQR106E

FAILURE TO OPEN THE LAYOUT TABLE

HCL Workload Automation for Z could not open the ready list layout table.

The system waits for you to respond.

Check that the ISPTLIB data set contains the EQQRLOUT table.

EQQR107W

A DEFAULT LAYOUT CANNOT BE DELETED

You have attempted to delete an installation-defined layout, but you are allowed to delete only your own layouts.

The request is rejected.

Check that the layout you attempted to delete is the layout you want to delete.

EQQR108W

THE LAYOUT RLLAYOUT CANNOT BE FOUND IN THE LAYOUT TABLE

The layout RLLAYOUT does not exist.

The system waits for you to respond.

Select one of the layouts in the list or create a new one.

EQQR109E

THE LAYOUT RLLAYOUT CANNOT BE FOUND IN THE LAYOUT TABLE

The layout RLLAYOUT does not exist.

The system waits for you to respond.

Select one of the layouts in the list or create a new one.

EQQR110E

THE LAYOUT ID MUST BE SPECIFIED

Data entry error.

Enter the required value and rerun the task to use the selected value. See Data entry errors.

EQQR111E

SELECT AN ITEM BY SPECIFYING SELECT OR A NUMBER 01-99

Data entry error.

Enter the required value and rerun the task to use the selected value. See Data entry errors.

EQQR112E

LEAVE BLANK OR SPECIFY OCHCYES OR OCHCNO

Data entry error.

OCHCYES is the national language character for Y (yes) and OCHCNO is for N (no).

Enter a valid value and rerun the task to use the selected value. See Data entry errors.

EQQR120E

NO LAYOUT WAS SELECTED, RSRLT IS USED

The ready list was to be displayed using the default layout, RSRLT, that is, the layout that was used last time the ready list was displayed for the same workstation. That layout could not be found and the first layout in the layout table is used.

The ready list is displayed.

If the used layout is not appropriate, change the layout ID.

EQQR121E

A LAYOUT MUST BE SELECTED TO DISPLAY ERROR LISTS

The Ended in Error List cannot be displayed without a layout ID.

A panel listing the possible layouts is displayed.

Select a layout from the selection list or specify a valid ID in the layout input field.

EQQR200E

INVALID PARAMETER WHEN CALLING MODULE MODNM

There is an invalid parameter in the input to the ready list module (module name MODNM).

The requested access to a ready list function is rejected.

Check that the panel has not been inadvertently overlayed in the panel library (ISPPLIB).

This message indicates that there is an error in the current panel.

EQQR201I

RETURN CODE URC WAS RETURNED FROM READY LIST USER EXIT

The active exit for this ready list layout ended with a return code greater than or equal to 8.

The status is not changed.

Contact the person responsible for ready list exit to determine the reason for the return code that was set.

EQQR202I

SET STATUS REQUEST CANCELLED BY USER EXIT

The active exit for this ready list layout has returned a code of 9 in the status field URNSTAT, which means cancel the request.

The status is not changed.

None.

EQQR300E

PRIORITY MUST BE A NUMBER 1 - 9

Data entry error.

Enter a valid value and rerun the task to use the selected value. See Data entry errors.

EQQR302E

SELECT THE WORK STATION TO DISPLAY A READY LIST

Data entry error.

Select the required field and rerun the task to use the selected value. See Data entry errors.

EQQR303E

A CHARACTER THAT IS NOT A STATUS CODE IS IN THE CODE STRING

A character that you have specified as a selection criterion for status codes is not a valid status code.

The system waits for you to respond.

Check panel EQQXINIX for valid values and reenter.

Contact your system programmer.

The convention on status codes for the installation is defined in the ISPPLIB library panel EQQXINIX.

EQQR400W

THERE ARE NO OPERATOR INSTRUCTIONS FOR THIS OPERATION

There are no operator instructions for the operation that you selected in the ready list.

The system waits for you to respond.

Check your input.

EQQR401W

JS AND JOBLIB DATA SETS CONTAIN NO JCL FOR THIS OPERATION

There is no JCL for the operation that you selected in the ready list.

The system waits for you to respond.

Check your input.

EQQR402W

THERE IS A JCL RECORD ON THE JS DATA SET, BUT IT CONTAINS NO JCL

There is a JCL record for the operation that you selected, but the record does not contain JCL.

The system waits for you to respond.

Check your input.

EQQR403E

CHECK JCL RECORD KEY: (JSADIDJSIAD JSIATJSOPNUM)

A read failed when trying to read the JCL record with the key JSADIDJSIADJSIATJSOPNUM. The key is derived from ISPF variables set up in a panel.

The system waits for you to respond.

Check that the panel has not been inadvertently overlayed in the panel library (ISPPLIB).

This message indicates that there is an error in the current or previous panel.

EQQR404E

STORAGE PROBLEMS OCCURRED

In a modify control plan (MCP) dialog for a JCL edit session the controller returned data that could not be retrieved and displayed, because not enough storage had been preallocated to receive it.

This message indicates that, in the ISPF environment, there is not enough main storage to receive and display the JCL modified and returned from the controller.

EQQR600E

STATUS ENTERED OR GIVEN BY EXIT MUST BE STR, STS, STI, STE, OR STC

Data entry error.

STR is the national language character for R (ready), STS is for S (started), STI is for I (interrupted), STE is for E (ended-in-error), and STC is for C (complete).

Enter a valid value and rerun the task to use the selected value. See Data entry errors.

EQQR601E

STATUS ENTERED OR GIVEN BY EXIT MUST BE STR OR STC

Data entry error.

STR is the national language character for R (ready), STS is for S (started), STI is for I (interrupted), STE is for E (ended-in-error), and STC is for C (complete).

Enter a valid value and rerun the task to use the selected value. See Data entry errors.

EQQR602E

ENTER OSOPSTS, OSOPSTI, OSOPSTE, OR OSOPSTC

Data entry error.

OSOPSTS is the national language character for S (started), OSOPSTI is for I (interrupted), OSOPSTE is for E (ended-in-error), and OSOPSTC is for C (complete).

Enter a valid value and rerun the task to use the selected value. See Data entry errors.

EQQR603E

ENTER OSOPSTS, OSOPSTE, OR OSOPSTC

Data entry error.

OSOPSTS is the national language character for S (started), OSOPSTE is for E (ended-in-error), and OSOPSTC is for C (completed).

Enter a valid value and rerun the task to use the selected value. See Data entry errors.

EQQR604E

ENTER OSOPSTI, OSOPSTE, OR OSOPSTC

Data entry error.

OSOPSTI is the national language character for I (interrupted), OSOPSTE is for E (ended-in-error), and OSOPSTC is for C (complete).

Enter a valid value and rerun the task to use the selected value. See Data entry errors.

EQQR615E

ONLY OPERATIONS WITH STATUS ARRIVING CAN BE SET TO READY

You have attempted to set an operation in the current plan to ready, but only operations with status arriving can be set to ready.

The system waits for you to respond.

Enter a valid status or leave blank.

EQQR616W

REQUEST TO SET THE STATUS TO STARTED IS IGNORED

You have attempted to set an operation in the current plan to started, but the operation has already started.

The request is ignored.

Enter a valid status or leave it blank.

EQQR617E

ONLY OPERATIONS WITH THE STATUS STARTED CAN BE INTERRUPTED

You have attempted to interrupt an operation that has not yet started. You can interrupt an operation only if it has already started.

The system waits for you to respond.

Enter a valid status or leave it blank.

EQQR618W

REQUEST TO SET THE STATUS TO ERROR IS IGNORED

You have attempted to set an operation in the current plan to ended-in-error status, but the operation is already set to that status.

The request is ignored.

Enter a valid status or leave it blank.

EQQR619W

REQUEST TO SET THE STATUS TO COMPLETE IS IGNORED

You have attempted to set an operation in the current plan to complete status, but the operation has already completed.

The request is ignored.

Enter a valid status or leave it blank.

EQQR620W

THE INTERRUPT REQUEST IS IGNORED

You have attempted to interrupt an operation in the current plan, but the operation has already been interrupted.

The request is ignored.

Select a valid request for the operation.

EQQR621E

DURATION REQUIRED FOR OPERATIONS THAT HAVE NOT BEEN STARTED

Data entry error.

You must specify a duration for operations that have not started. Enter the required value and rerun the task to use the selected value.

EQQR622E

AN OPERATION WAITING FOR ARRIVAL CANNOT BE RESET

You have attempted to reset an operation that is waiting for arrival. This is not allowed.

The system waits for you to respond.

Enter a valid status or leave blank.

EQQR623E

AN OPERATION WITH READY STATUS CANNOT BE RESET

You have attempted to reset an operation that is ready. This is not allowed.

The system waits for you to respond.

Enter a valid status or leave blank.

EQQR624E

OP BEING UPDATED BY ANOTHER USER, REQUEST IS REJECTED, RSNC: XSSRS

The operation either cannot be read from the current plan or has another status, real duration, or error code than is displayed. The operation has been changed from its condition in the ready list.

The ready list is refreshed and the system waits for you to respond.

Review the operation, and if it is still valid, reenter the request.

EQQR626E

THE REQUESTED STATUS CHANGE MUST BE DONE VIA A RESET REQUEST

The intended status change is not supported. You must enter a reset request and a request to get the desired status.

The ready list is displayed.

Enter the row command R and enter N-x, where x is the required status.

EQQR627E

RESET OF OSEQ OPERATION MUST BE DONE VIA MODIFY CURRENT PLAN

You attempted to reset an operation with error code OSEQ from the Ready List dialog. This cannot be done. The error code OSEQ indicates that a job began to execute before all the predecessors to the operation were complete.

The ready list is displayed.

Reset can be done when all predecessors to the OSEQ operation are complete. To reset the operation status to Waiting, issue the operation command RERUN from the error list in the Modify Current Plan dialog.

EQQR629E

THE JCL IS BEING UPDATED BY USER &USR, REQUEST IS REJECTED

You have attempted to update the JCL, but it is being updated by another user &usr.

The request is rejected and the system waits for you to respond.

Try again later.

EQQR638E

WHEN SETTING STATUS TO OSOPSTI, SPECIFY DURATION OF OPERATION

Data entry error; see Data entry errors.

A duration of operation is required when setting the status to OSOPSTI, the national language character for I (interrupted).

You must specify a duration of operation when setting the status to OSOPSTI, the national language character for I (interrupted). Enter the required value and rerun the task to use the selected value.

EQQR639E

WHEN SETTING STATUS TO OSOPSTE, THE TYPE OF ERROR MUST BE SPECIFIED

Data entry error; see Data entry errors.

You must specify a type of error when setting the status to OSOPSTE, the national language character for E (ended-in-error). Enter the required value and rerun the task to use the selected value.

EQQR640I

THE JCL FOR THIS OPERATION CONTAINS UNRESOLVED SETUP VARIABLES

You tried to resolve variables using the program interface request JCLPREPA, with SIMTYPE FULL, and HCL Workload Automation for Z found one or more unresolvable variables in the JCL for the operation.

None.

Browse the HCL Workload Automation for Z message log data set (EQQMLOG) for message EQQJ510, which gives you the name of the failing variable. Correct the failing variable and retry the request.

EQQR656E

THE VALUE ENTERED DOES NOT MATCH THE VARIABLE'S VERIFICATION RULES

Data entry error.

The value that you entered is invalid according to the validation criteria defined for this variable.

Use the S row command to check if help is defined for the current variable. If no help is defined, contact the person responsible for variable definitions to see what rules apply to the variable. See Data entry errors.

EQQR657E

A VALUE MUST BE ENTERED FOR THIS VARIABLE

Data entry error; see Data entry errors.

According to the definition of this variable, a value must be entered.

Enter the required value and rerun the task to use the selected value.

EQQR658E

THE EDIT OPTION CHARACTER MUST BE Y OR N

Data entry error; see Data entry errors.

Enter Y (yes) or N (no) and rerun the task to use the selected value.

EQQR662E

A VARIABLE WITH VAL REQ=Y MUST NOT HAVE A BLANK VALUE

If it is specified that a JCL variable requires a value other than blank, the default value must not be blank.

The system waits for you to respond.

Insert a default value other than blank in the Default Value field.

EQQR674E

AN ERROR OCCURRED DURING INSERT HANDLING

An error was detected during INSERT JS PROGRAM INTERFACE (PIF) processing. This message is issued in the EQQMLOG for the PIF job when a user tries to add a JCL already present in the JS file.

The job is terminated with a return code of 0.

Correct the errors and retry the request..

Check the controller message log (EQQMLOG) for messages describing the error.

EQQR675E

AN ERROR OCCURRED DURING JCL-VARIABLE SUBSTITUTION

An error was detected during JCL variable substitution processing. This message can be issued to a:
Dialog user
In the JCL Setup dialog to indicate that an error has been detected during variable substitution
PIF application
In the EQQMLOG for the program interface (PIF) job when any type of substitution or validation error occurs.

In the dialog, the system waits for you to respond. If the error occurred while using the PIF, the job is terminated with a return code of 0008.

Correct the errors and retry the request.

In the dialog, look at the detailed error message that has been inserted into the JCL. You can find the message by entering ISPF command LOCATE SPECIAL.

If you are using the PIF, check the controller message log (EQQMLOG) for messages describing the error.

EQQR676E

AN ERROR OCCURRED DURING JCL MEMBER READ

An error occurred while reading a JCL member.

The request is rejected.

Either the JCL is not present in the JOBLIB data set, or an access problem occurred while the JCL was being read.

EQQR701E

GROUP ID INVALID. ALARM=YES

Run cycle group name is missing or invalid.

No action is taken.

Enter a valid run cycle group name.

EQQR702E

PERIOD/RULE MISSING. ALARM=YES

A period/rule name must be specified.

No action is taken.

Specify a valid, existing period or rule name.

EQQR707E

RUN CYCLE GROUP EXISTS. ALARM=YES

A run cycle group with this ID already exists.

The system is waiting for a valid, pristine ID.

Enter a brand new run cycle group ID.

EQQR708E

RUN CYCLE GROUP IN USE. ALARM=YES

The run cycle group is being updated by another user. Try later.

No action is taken.

Retry later.

EQQR709E

THE RUN CYCLE SUBSET ID IS INVALID

One or more invalid characters were used in the subset name. Only alphanumeric characters are admitted.

The run cycle is not saved.

Use only alphanumeric characters to specify the subset name.

EQQR711E

A PERIOD NAME MUST BE SPECIFIED

See text.

None.

Specify a correct value and press Enter.

EQQR712E

THE PERIOD NAME DOES NOT EXIST IN THE CALENDAR

The period name that you specified is not defined in the calendar database.

The system waits for you to respond.

Enter an existing period name, or use the Calendar dialog to define the period name.

EQQR713E

A VALID RULE NAME MUST BE SPECIFIED

You have not entered a valid rule name. A valid rule name has a maximum of 8 characters, where the first character is alphabetical and the remaining characters are alphanumeric or national.

The request is rejected.

Specify a valid rule name.

EQQR714E

SPECIFY AT LEAST ONE RUNDAY

You selected a period, but failed to specify any offsets.

None.

Specify an offset and press Enter.