Home
Test Execution Specialist Guide
This guide describes tasks that you must complete before you can configure and run tests in Rational® Test Automation Server. You can find information about other tasks that you can perform on the Resource Monitoring Service, Virtualization, and Integrations with third-party applications. This guide is intended for testers or test execution specialists.
Agents overview
You can find information about the agents that you must install on remote computers and configure the agents with the offline user token so that the agents register with HCL OneTest™ Server. After the agents are registered, you can add them to your projects and then select them as locations to run tests.
Adding an agent
If you have performance tests that distribute workload across different workstations or Accelerated Functional Testing (AFT) Suites that need to run on different platforms and browsers, you can add IBM® Rational® Performance Tester Agents to your projects to run tests on remote workstations.

Test Execution Specialist Guide
This guide describes tasks that you must complete before you can configure and run tests in Rational® Test Automation Server. You can find information about other tasks that you can perform on the Resource Monitoring Service, Virtualization, and Integrations with third-party applications. This guide is intended for testers or test execution specialists.
- Prerequisites to running tests
  Before you can configure and run a test in a project on Rational® Test Automation Server, you must read the information about the different tests. You might want to add a remote static agent or a remote Docker host to the project as an alternate location to run the tests.
- Agents overview
  You can find information about the agents that you must install on remote computers and configure the agents with the offline user token so that the agents register with HCL OneTest™ Server. After the agents are registered, you can add them to your projects and then select them as locations to run tests.
  - Test run considerations for running tests on remote agents
    Before you configure a test to run on a remote agent, you must read the considerations you must take into account.
  - Adding an agent
    If you have performance tests that distribute workload across different workstations or Accelerated Functional Testing (AFT) Suites that need to run on different platforms and browsers, you can add IBM® Rational® Performance Tester Agents to your projects to run tests on remote workstations.
- Managing Docker hosts
  You can set up dedicated external Docker hosts to run large tests or run tests remotely to free up the dependency of running tests on the internal Docker host of IBM® Rational® Test Automation Server.
- Test run configurations
  You can configure and run tests in IBM® Rational® Test Automation Server after you add the test resources to your project.
- Management of running tests
  Find information about the tasks that you can perform on a test that you configured for a run either while it runs or after it completes the run.
- Management of virtualized services
  You can find information about the tasks that you can perform on and manage the virtualized services that run on Rational® Test Automation Server. You can start or stop the stubs connected to Rational Test Automation Server. You can view the stub usage statistics and the routing rules configured for the stubs, agents, or proxies that are connected to Rational Test Automation Server.
- Test results
  After the tests or schedules are run and completed, you can view the results and reports in IBM® Rational® Test Automation Server to analyze the verdict, the performance, and statistics. You can also re-execute tests and schedules from the Result page with the same commit id.
- Resource Monitoring service
  When you apply load to a system under test, the amount of resources consumed by your system is increasing. If the capacity of the resources does not match the load, you can see performance issues in the results. The Resource Monitoring service in Rational® Test Automation Server helps you monitoring the resources of a system and establish the performance metrics of the system. Thus, you can observe the health of these resources while a schedule is running.
- Integrating with other applications
  You can integrate certain applications with IBM® Rational® Test Automation Server to run tests and view the test results.
- Managing access to the server
  Desktop clients and third-party integrations use offline user tokens to connect to Rational® Test Automation Server.

Adding an agent to the project for running tests

If you have performance tests that distribute workload across different workstations or Accelerated Functional Testing (AFT) Suites that need to run on different platforms and browsers, you can add IBM® Rational® Performance Tester Agents to your projects to run tests on remote workstations.

Before you begin

You must have completed the following tasks:

Read about the considerations you must take into account before you configure a test run to run on a remote agent. See Test run considerations for running tests on remote agents.
Been assigned the Owner or Tester role in the project to which you want to add the agent.
Owned at least one agent that is not added to the project.

About this task

When you configure the agent to connect to the server, you specify an offline user token. This token defines your ownership over the agent. Only you can add or remove this agent from the project. However, any member of your project with the permission to run the tests can initiate the run of the performance schedule and AFT Suites that are associated with the agent.

Procedure

Log in to Rational® Test Automation Server, open your project, and go to the Infrastructure page.
Click Add Agents.

The agents that you configured with your user token are displayed.
Select the agents you want to add to the project from the agents displayed.

Results

You have added remote agents to your project.

What to do next

You can run the tests on the agent added to the project from the Execution page. See Test run configurations.